General Discussions

For anything and everything that doesnt fit in other categories.

29
1
Can anyone please give me an idea about how we connect three wire strain gauges to the data taker and what bridge configuration we should follow? I am using a DT85 model data taker.

If anyone can explain the basic things related to this or provide some useful links, it would be a great help as I am very new to data taker.

Thank You.

103
1
Beshoy Kameel posted Dec 17 '20 at 8:04 am
Hi,

I've been using a DT85 series 4 for logging several 4:20mA signals, and I'm configuring the DT-85 using DEX-2.
the DT85 had displayed all the signal correctly on its display, however when I tried sending a CSV file using FTP, nothing was sent to the FTP server.

her is the DXC

BEGIN"config"
'Generated by new dEX-2
password=""

S1=0,500,4,20""
S2=0,5000,4,20""
38
0
vvsang84 posted Jan 13 '21 at 6:02 am
Dear Team,
I'm facing to the Flash that is out of date. I can not access to Dex software to configure data taker DT80. Please help to instruct me to configure it.
Thanks
Sang

50
2
neceel posted Sep 25 '20 at 12:44 pm
Hi,
I´m trying to send via serial a variable inside CV, also this I´m trying to send the timestamp.
How is the syntax to send the content of the variable via serial?
I tryed these:
1SERIAL("\w[500]\e{#001SCK<?(timestamp)>7A\013\010}\m[001SCK<>16]")
1SERIAL("\w[500]\e{#001SCK<?(500cv)>7A\013\010}\m[001SCK<>16]")

Best Regards

Neceel

27
2
Rheniumjoe posted Aug 25 '20 at 7:49 pm
Hello,
I am using a DT82E and I was wondering if there was a way to display/report the loggers internal temperature or tell what it is using as a cold junction compensation temperature for thermocouples. I am looking at the mV output and it must be compensating for the cold junction temperature, but I cannot tell where or how.

159
3
Hi all,
I have a DT80 series 4 , I want to connect a Power analyzer with RS485,
Protocol communication: Modbus RTU
• Baud rate : 4.8, 9.6, 19.2 kbps
• Parity number: Odd, Even, None
• Stop bit: 1,3
• Address: 1-247
• Connectors : 4 pole terminal ( integrated 120 Ohm terminator on T terminal ),
So, I need your help for the configura
37
3
neceel posted Nov 26 '19 at 10:19 am
Hi,

I have a problem.

We have several systems powered by a battery and a solar panel (12v 38Ah, 50W).

The problem is that when the weather is bad, the battery lasts a few days.

How can I make good energy savings?

Best Regards
Jonathan Maida

41
1
Gonzalo posted Sep 2 '19 at 1:53 am
We need a simple way to totalizer a slow pulse from water meters and the same time reset counter each datalogging. Reset is easy using dEX with “Reset Counter”, but ”doesn’t exist the “Totalizer Counter for ever”

Thanks in advance

22
4
I realize this probably isn't the correct forum to ask about Cybertec 1100 but there seems to be a bunch of networking pros here with some experience with Cybertec 1100, so here goes.

I am trying to make wireless dial in a Cybertec 1100 using hyperterminal with TCP/IP. Since wireless IP address are quite expensive over here, I will use dynamic IP with DDNS on the modem.

Registered with
recent by Old Forum  ·  May 16 '19 at 3:35 pm
12
1
Old Forum posted May 16 '19 at 2:54 pm
Current profile in a remote location, GPRS network weak with frequent signal breaks. Current profile data very 10 minutes:

16 C811 70802 2008 3 28 12 21 52 3 0 1 2 40 200 100 10 1
0 0 0 2886 17424 0 0 0 0 0 15425
0 0 0 0 61 191 65 193 14 16 18 0 110 192 0 107
1 -1399 -2174 -172 0 0 0 129 131 162
2 -1412 -2378 -294 0
recent by Roger  ·  May 16 '19 at 2:55 pm
33
2
Old Forum posted May 15 '19 at 4:26 pm
Here is a quote from Datataker Australia:


USB Memory Stick: We do not recommend the use of USB flash drives for logging as they are not robust and the DT80 does not have any retaining mechanism to retain the drive, it can fall out.


Does "DT80 does not have any retaining mechanism to retain the drive, it can fall out" means the USB stick PHYSICALLY fall off the slot? or does it mean data
recent by Roger  ·  May 15 '19 at 4:28 pm
95
232
1
Actions
Hide topic messages
Enable infinite scrolling
Previous
Next
All posts under this topic will be deleted ?
Pending draft ... Click to resume editing
Discard draft