szymon
posted Jun 9 '22 at 5:19 pm
Hi,
I'm pretty new to Dex2 and DT and I'm trying to connect a power meter using Modbus RTU (RS 485) to Serial Port in my DT85. I've tried to write my own script with help of many code examples found in internet which didn't work. I also tried to program DT with Dex2 using graphical features it provides.
Code below is generated by Dex2:
And this is code I wrote which can't be eve
alan
posted Jun 8 '22 at 11:45 am
Hi i am looking to save to a CV channel the time stamp of when temperature sensor connected to the DT85 reaches a certain temperature 75C. therefore the CV channel will merely have the time this occurred
Lan
posted Jun 5 '22 at 2:05 am
What model datataker can support 4g/5g communication
I have somehow locked myself out of my DT80M logger. In the Dex 2 software I set user level security to on by mistake. Now when I try to connect to the logger from DEX I get asked for a user name and password. I have guessed the default as datataker and datataker as defaults without success. How do I reset this I cannot see an obvious way.
Regards
Andrew
rberndt
posted May 31 '22 at 3:31 am
Hi
I'm trying to add a ultrasonic RS485 sensor to my schedule on a DT85 ser 3 still using web interface.
https://wiki.dfrobot.com/URM14_RS485_Precision_Ultrasonic_Sensor_200KHz_SKU_SEN0358
The sensor has 4 wires: orange V+, black gnd, blue RS485-B, white RS485-A
My datataker supplier has kindly helped out by noting connect blue RS485-B to RTSY and white RS485-A to TxZ terminals.
Mahi
posted May 21 '22 at 3:36 pm
Hi
I am using datataker Dt85. I am using web browser for configuring it Whenever I change the schedule and download it , the previous logged data is deleted
Can anyone suggest a workaround.
Should I use DEX instead of browser
Gonzalo
posted May 14 '22 at 10:34 pm
DEX2.0 for Windows and MacOS.
I´m working over newer DT80W and DT82E and stability´s DEX2.0 is not good. I´m not sure if the FW DT8X or if the recently update of Windows of MACOS.
DEX 2.0 the problems are the same. When "apply to datalogger" DXC sometime fails and I must start full configuration again. It hangs up.
Siyuan
posted Apr 21 '22 at 4:24 pm
Hi,
I am a new user of Datataker DT85. Some of the thermocouple readings show a large instant jumping up (about 1~3°C) which is unreasonable and groundless although I do not change anything.
Also, when I turn on the humidity sensor power supply, the readings of the thermocouples are jumping about 10 °C.
Could you help give some advice about this problem? Many thanks.
Rega
R Chua
posted Apr 26 '22 at 2:05 am
Now that Adobe has discontinued Flash Player, what has replaced it in order to display dEX2 data on Windows or IOS?
mirfan1
posted Apr 3 '22 at 7:34 pm
Hello,
I am a new user of DT85GM (and CEM20). I am going to use DT85GM for performing load test wherein we plan to use vibrating wire strain gauges and LVDTs (load cell is planned to be connected to another data logger).
Since my background is in Civil Engineering so going through all the details of the user manual appears to be a time consuming task, something that our project timelines d
acavaco
posted Mar 31 '22 at 5:56 pm
Hello,
I am trying to set a statistical routine that measures every 5s.
Then I have an routine for the 1 minaverage values of the 5s measurements.
Applying statistics:
values registered:
My issue here is that the values being registered do not match the ones I want to have. It is also saving the instantaneous 1 min value of the variable. Is there a way not to save t
We are using the DT85 to track temperature data by the second with both k-type TC's and RTD's. We are converting the C degree to F with Polynomial 1. What we are finding when we export our data to CSV is that the temperatures have 6 decimal places. Is there a way to round these up/down before exporting?
We have just started using our DT85. It was working great in testing but now we have an issue. We are getting a DXC Compilation Failure when we connect with dEX-2. What could cause this and how could we remedy this? And now we can only connect 1 instance of dEX-2 at a time. Trying to connect on other devices at the same time causes the DT85 to shut down and reboot - then only one connects to it a
acavaco
posted Mar 30 '22 at 6:40 pm
Hello,
I have several DT80 running in radiometric stations. Now, I need to make modifications to the program of one the stations and seems to me I have to do it from scratch because I cannot modify the old program (which is very long...)
I want to program this part in the new "language":
T(w,=1CV)
I have tried to do a manual to insert it.
However, when I check the value of 1CV i
Dear Team ,
Good Day to All , Hope you are doing great.
I am Mohammed Riyaz from Emirates Global Aluminium , Dubai , UAE.
We are using DT85 device for data acquisition and logging instruments. Currently we are fetching measured data through USB device which is manual process.
To save time & reduce man power we thought to automate this manual process , so we have decided to f
I have multiple DT85 devices (both 3 and 4). One of the series 3 units can be seen by DEX2 using either USB or ethernet connection but when I try and check connectivity it always says "Device Offline". It changes the light indicator on DEX2 from red to yellow.
I saw another post that said to check the console errors. Unfortunately, I do not have any console errors as DEX is seeing that there
Hello,
I am having an issue where the DT85M occasionally stops logging and the commands stop working. When I try to send commands I get a "Permission Denied" response, even though I am logged in as an admin.
I am getting a lot of E9, E10 and E12 errors. From a previous forum post it looks like it could be caused by commands leaked through the network. However, I have commands password prote
I use a DT82i with one device connected on rs232 host port. I retrieve the data frame from this device by decoding on a manual channel. Some values are sometimes negative due to the background measurement. I record the average of these values on CV every 10 min. I would like eject the neg values, how may I proceed ?
Thank you
There is no session time window for ethernet connections. Is it possible to wake up the datalogger for certain time windows, in order to access it remotely over ethernet? We have a battery powered site with a radio link. The datalogger is connected to the radio modem over ethernet. In order to safe power, the datalogger stays in a low power mode and wakes up every day once to do measurements and
besim
posted Nov 23 '21 at 8:09 pm
Hello Guys
I really can't help myself with this problem
I Storing My data daily in DBD Format on the internal file system of the Datataker. There are 4 Schedules
The First three are unloaded without a Problem but when it gets to the Last one it gives me the Error E110 Error Accesing Storefile.
Has anyone Experience with this kind of problem I can't explain it
Does anyone know how to data average with dex2? I have a calculated channel for a flow meter and would like to smooth the data out.
thanks..
RESOLVED - - -
I have been trying to connect a DT85 series 3 logger to a windows 10 laptop for over a month, and am still having the same issues. Even with the most up-to-date deX2 and DT-USB software, my laptop is not recognising the logger when it is connected, and therefore, isn't opening the browser or letting me access any data.
It has been suggested that a firmware update (from 9.18
alan
posted Oct 28 '21 at 3:15 pm
Hi is it possible to have an on screen mimic button which can be clicked to change a cv value or a DSO ?
Is there a way to turn HOST_PORT (2Serial) on and off within JOB?
I tried this procedure:
RB"Sigfox_ON"("b:",ALARMS:OV:100KB:W60,DATA:OV:1MB)1H
LOGONB
DO{PROFILE HOST_PORT FUNCTION=SERIAL};
DO{XC}
RC"Sigfox_DATA"("b:",ALARMS:OV:100KB:W60,DATA:OV:1MB)X
LOGONC
2SERIAL("{%d[1CV],%E[1001CV],%d[2CV],%E[1101CV],%f[1501CV],\013\010}");
DELAY(W)=12000
DO{PRO
brian r
posted Oct 15 '21 at 4:16 am
While I've seen charts that compare Datataker units of the same era/series, are there any charts that provide a per-series comparison of the same devices?
I.e. DT85 vs DT85-2 vs DT85-3 vs DT85-4
brian r
posted Oct 10 '21 at 1:44 am
I've got a DT85 Series 2 with the latest 9.22 firmware and am configuring it with dEX-2 v2.1.25 but when I have it reading a couple of voltage channels I'm hearing internal relays clicking each time, is this normal? Although the expected values are correct, the noise is annoying. Am I missing a setting somewhere?
If its relevant, I'm making readings from pins 2 & 3 from the 4-pin connect
Is CEM20 series 2 compatible with DT85 series 4 and DT80 series 3?
Hi, I had dex2 and delogger installed and running fine on a previous laptop with win10. I have just upgraded to a new surface pro, and I am getting an error for the usb driver . In device manager the following info is displayed for the DT8x datalogger
Windows cannot load the device driver for this hardware. The driver may be corrupted or missing. (Code 39)
{Bad Image}
%hs is either no
آن کف مطلع بهترین مهم مراقب کوچکی نکنید کردن دهد. ندارند نتایج می یک ک
Ozone Wallet: An Offline Wallet with Special Features Ozone is a scientific group including cryptocurrency experts who present an Offline Wallet in order to ensure traders and investors’ security. As is known, in a cold wallet, the user is not completely disconnected from the internet and in some cases, a World Wide Web connection is required for setting up. Hackers are aware of this mat
