Hi, 2 questions for you.

Configuring a current probe, the type that clamps around the power cable like a clothes peg. The output is 1mV per amp (I'm measuring up to 42 amps). The signal is a fixed frequency (looks like 50Hz) and the signal is the variation of the peak to peak voltage. I'm not getting a consistent reading. How should I wire this to the DT800 (I am connecting the 2 cables to t

Hi,

Using Delogger and a DT800 is it possible to use an analogue channel (radiometer logging at 1 sec) to trigger another analogue channel (laser logging at 1 sec) into burst mode for a period of 60 secs and then stop it again.

What I am doing is, using a radiometer I am measuring radiation kW/m2, when this reaches a certain value I want to be able to put a laser into burst mode for a p

Hi,

I have no problems to access to the DT800 via telnet, sending the DT800 commands. But I can not access to the DT800 File system via ftp. I can logged in (with user:ANONYMOUS, and password:PASSWORD), but nothing else.

I can not neither see nor get the files. In theory, as the user.ini says, the DT800 support ftp communication. I suppose the problem is that I am not sending the correc

We have been testing a DT800 using 3.99.13 beta firmware and have had some problems with losing contact with the logger using Ethernet connection.

Each time this happened we connected serially to the logger and check the status. This worked without problem and we couldn't detect any reason for the Ethernet comms problem.

To restore Ethernet communication we had to reset the logger, SING

Roger,

The analogue output on the DT 800.... how do you control it? Is it possible to perform an operation like: "If the current at channel 1 falls below (say) 12.5mA then increase the analog output current by 10%" (For current read voltage, I would be able to work with either one.)

Does anyone know what the FMT channel modifier is? I think it is something like FAST mode but can't find it in the manual.

Thanks,
Derek.

G'day Roger

Upgraded an 800 to 3.99.007 and noticed there was no information under the serial tab of the status check with the new version of firmware. DeLogger 4 details are version 2 release 15 service pack level 2.

Hi,

I was wondering if the serial channel can communicate with SPI devices? Has anyone done this? Is SPI just SDI-12 with the option to set the baud rate to something other than 1200?

Derek.

On my DT800 after I use command ?ALL I get alarm details followed by ?? SELF DIAGNOSTIC: "Bad Default" DCOutput.. c 974 I then have trouble with communication to the logger and have to do a hard reset to continue.

I am communicating through the ethernet port and have a GSM modem connected to the serial port. I am using Delogger. What can cause this error.

I am conducting a series of tests where I need to reset the cumulative counters for the start of the next test. So far, the only way I have been able to reset the counters is by Hard Reset (Reboot) of the data logger.

There must be a better way. Ticking the resetting option in the counter panel does not provide the correct data.

Hello everyone,

Is there any word on when the Labview Drivers will be available? I'm about to start a new Labview project with a DT800 and I will need drivers. It will save me a lot of work if I don't have to write my own.

Thanks.
Derek

I have two schedules running; one at 40 ms and one at 1 s. I need to align the data output from both schedules for comparison. Any suggestions on how this can be accomplished easily?

At present the data for the 1 s schedule is tagged on after the 40 ms schedule which presents a lot of additional work. I have tried using both the replay files and csv files in MS-Excel and not had any success.

Hi,

I seem to be unable to put my DT800 to sleep. When I stop a program (logging) and disconnect from the DT800 it seems to be still acquiring something. It will continue to do this until the internal battery runs out of power.

I am using Delogger 4 Pro. Can anyone help me?

Much Thanks,
Sean

Hi all,

Just wondering if anyone has any experience with reading an 800 from a Mac via Ethernet? We're considering using one a localized measurement point in our lab and are weighing up a few options.

I understand using a terminal emulator can be used on a Mac to DT600, so I'd guess it's a case of using third party software.

Mitch

Good morning,

I have some difficulties with a DT800. I power it with an external battery (12 Ah). The consumption seems to be abnormal. The battery is empty after 15 days (17 resistance channels every 5 min) logging.

Is there a problem ? I think yes. The sleep mode is P15=1. Thank you.

I recently collected a large amount of data from an application in which the DT800 did not have continuous input power. I had the program set as the RESET job so that if the internal battery died, it would start collecting data again as soon as power was reapplied.

The logging worked perfectly, however (there is always a however!), when uploading the data the logger had a problem at the brea

I am using two DT800's one with the beta firmware and one with V 3.16, when connected via the Ethernet connector after a random period of time the DT800 hangups or goes to sleep.

The only way to get them started up is to disconnect and reconnect the power ( I am using the plug pack input) or push the reset button. Does any one else have this problem or are there still limitations in using th

I am logging 4 channels to a compact flash memory card (64 MB) in Fast mode. After reading through the manuals to optimize speed, I discovered that the unit will not write to compact flash nearly as fast as it writes to internal memory -- I was getting about a factor of 10x slower! Is there anything I can do to speed the logging to compact flash.

I need the extra memory in order to log a lar

Currently, DT800 are not able to excite vibrating wires. I want to buy a new DT and it's difficult for me to choose the DT515 (vs DT800) because of this problem of vibrating wires. In the future, will exist DT800 (or DT815 !) which can excite vibrating wires.

When ??? I would be very interesting.

Thank you.

Hello,

Currently we have several DT800s that we use for data logging, which run at 4 Hz. However, I would like to use the burst feature of the DT800 to record current and voltage characteristics of electric motors and motor controllers.

Ideally, I would like to sample at rates of 1 kHz to 10 kHz for periods of a couple of seconds up to several seconds. I have a couple of questions: