Support Forums

Have any problem? Report it here and we will be glad to help.

44
3
Dear Sir,

we are using DT85 for measuring strain gauges (full bridge) for load measurement. when we are configuring channel 1 , 2 and 3 for BGV and not connecting any strain gauges, we are getting reference error. this implies no gauge is connected. this is ok. but when we are connecting one strain gauge to channel 1 and no strain gauge is connected to 2 and 3 channels - we are getting say
recent by admin  ·  Apr 19 '19 at 3:11 pm
26
2
FrankI posted Apr 19 '19 at 2:57 pm
Hi All,

Just want to say that I'm a newbie using the DT85, but we're very pleased with the performance. I have two immediate questions.

1) on page 26 of the DT85 manual it describes the format of the CSV format of the logged data, and it appears by default that the date is included as part of the timestamp. My logged data only contains the time, no date. How do I correct that?

2)What
recent by Roger  ·  Apr 19 '19 at 3:08 pm
113
5
Friedrich posted Apr 19 '19 at 2:58 pm
Hi,

I am trying to communicate via the RS232 host_port with a controller. The controller uses ASCII protocol (38k4, 8N1). With hyperterminal I can communicate with the controller, I get an answer back. With the datataker I get a timeout on the read.
The command I use is: 2SERIAL("\e{:06040401210120\013\010}%s[1$]"). When I send the command to hyperterminal, it looks if it has the correct
recent by Friedrich  ·  Apr 19 '19 at 3:04 pm
49
3
Peter_A posted Apr 19 '19 at 1:35 pm
Hello everybody!

I have trouble programming dataTaker DT85.

I would like to make a job with 4 different schedules:

First schedule should start every monday at 00:00 til 09:00 am.
It should sample and log data (voltage) every 10 min and put digital outputs 1D and 2D in to a known state.
I had an idea how should it look:

RA10M"UC_pr1"("b:",ALARMS:OV:100KB:W60,DATA:OV:10MB)[:::
recent by admin  ·  Apr 19 '19 at 1:41 pm
17
1
afrididx posted Apr 19 '19 at 1:27 pm
I am using DT85 for Voltage and Temperature Monitoring and use ONISERT.DXC file but DT85 accept only SCANDISK 4GB disk. If I wan to use other Brans it does not recognize. So please Tell me that Weather DT85 recognize only Scandisk Flash drive or other bran also.

Hope to get proper Reply

Aslam

recent by admin  ·  Apr 19 '19 at 1:34 pm
72
3
I was given a DT85 series 2 at work but I cannot connect it to the computer. The problem is that it constantly disconnects and reconnects every 5-10 seconds (it is connected to its ac adapter, which is working fine because i tested it on another DT85).

I don't know if it is a firmware problem but even if it is I can't update the firmware because of the constant disconnections and when I trie
recent by admin  ·  Apr 19 '19 at 1:33 pm
22
4
afrididx posted Apr 19 '19 at 1:28 pm
Good Morning Rudy,

Please guide me, that I want to use mV input with 0.5s frequency and Temperature with 1 minute frequency then do some calculation using these input. Is it possible in one DT85 in one program Schedule or I need to write Schedule A for mV and Schedule B for Temperature and then these data can be use for calculated out put.

Regards
Aslam Khan

recent by admin  ·  Apr 19 '19 at 1:33 pm
33
4
edie posted Apr 19 '19 at 1:20 pm
Hi,

I've been using a DT85 series 3 with 4 CEM20 and I'm logging temperatures using RTD sensors.
I don't really care, is it possible to log and store my data in two different files, once every hour and average per day?
I've done some research on the DT85 manual but I can't find is it possible to configure the DT85 with two job's?
What I need is hours and daily data in two different
recent by admin  ·  Apr 19 '19 at 1:25 pm
15
1
tolgasirlan posted Apr 19 '19 at 1:16 pm
I have problem with my modem connection to DT85G.

I have got AT command modem and I am using below string codes as mentioned in DT85g manual which is wavecom supreme GSM modem;

AT&S0
AT&D2
ATS0=4
AT&C1
AT+IFC=2,2
AT+ICF=3,4
AT+IPR=57600
ATE0
AT&W

and I am using this code for DT85g

PROFILE "HOST_MODEM" "INIT"="AT"
PROFILE "HOST_MODEM" "SEN
recent by Roger  ·  Apr 19 '19 at 1:19 pm
31
3
RPE_GER posted Apr 19 '19 at 1:07 pm
Dear DT85 Users,

it's posible to send comands, like over serial "1serial(".....{....}")", over Ethernet?
I want send a comand line to a specific IP and port.
I dont find any code examples.
I tried very difrent comand syntax but nothing works.

Maybe someone can me help.

Thank's so much.
Ralf

recent by RPE_GER  ·  Apr 19 '19 at 1:14 pm
250
22
edie posted Apr 19 '19 at 10:56 am
Hi all,

once installed, followed all the directions the Tech Notes TN-0043-A0 “Using FileZilla FTP Server with a DT80 Series Logger“,
but I can not upload files to FileZilla FTP Server.

I have checked all connection settings and seem to be okay according to the instructions.

There is no antivirus or firewall software on the computer installed.
I have checked the Wind
recent by admin  ·  Apr 19 '19 at 1:03 pm
93
3
edie posted Apr 19 '19 at 10:55 am
Hi All,

I have a DT85 Serie 3 dataTaker and I am trying to upload via FTP data to a file server.
I have followed all the directions the Tech Notes TN-0043-A0 “Using FileZilla FTP Server with a DT80 Series Logger “, but I need some help.

This is how I tried to do it: I have already installed and tested FileZilla Server on a local PC running Windows XP and assigned static IP
recent by edie  ·  Apr 19 '19 at 11:06 am
43
7
FrankI posted Apr 19 '19 at 9:50 am
My application involves logging data for varying ESS cycles. Depending on the product, the lengths of these tests vary. Once the user starts the logging, I'd like to send out an email (create an event) after a certain amount of time has elapsed. How is this done? I read about time triggers, is that the way to go?

If I did a Timed Trigger with Synchronize to Midnight disabled, could I have a s
recent by admin  ·  Apr 19 '19 at 10:51 am
19
2
FrankI posted Apr 19 '19 at 9:56 am
Hi All,

Below is a job I wrote for detecting when 5 pulses are counted at an input, it works fine, but what I really need is to detect the falling edge, how is this done? Can with a xD input also?

The output results are attached.

Thanks

BEGIN"MIMIC"
RS1S
RA"Sched_A"(….)1S
LOGONA

1HSC("Counter_1",LM)

RB"Sched_B"(….)1HSC(5)
LOGONB

5DSO("WriteALo
5cb98d2c4abd9
recent by FrankI  ·  Apr 19 '19 at 10:38 am
14
2
I have tried to set up a daily schedule to save newly acquired data to a USB memory stick.

I set this up in dEX configuration builder by adding a new schedule to run every day at midnight, then added a manual channel with the command

COPYD dest=A: format=csv archive=N src=BD start=new;

If I issue this command in the command window, it successfully saved data to the USB device.

Wh
recent by admin  ·  Apr 19 '19 at 5:26 am
668
2.63k
3
Actions
Hide topic messages
Enable infinite scrolling
Previous
Next
All posts under this topic will be deleted ?
Pending draft ... Click to resume editing
Discard draft