My application involves logging data for varying ESS cycles. Depending on the product, the lengths of these tests vary. Once the user starts the logging, I'd like to send out an email (create an event) after a certain amount of time has elapsed. How is this done? I read about time triggers, is that the way to go?

If I did a Timed Trigger with Synchronize to Midnight disabled, could I have a s

Hi All,

Below is a job I wrote for detecting when 5 pulses are counted at an input, it works fine, but what I really need is to detect the falling edge, how is this done? Can with a xD input also?

The output results are attached.

Thanks

BEGIN"MIMIC"
RS1S
RA"Sched_A"(….)1S
LOGONA

1HSC("Counter_1",LM)

RB"Sched_B"(….)1HSC(5)
LOGONB

5DSO("WriteALo

Guys,

I followed all the directions from TN0042, but when I go to rename the "needa" and "jango" folders, I get the following error message.

See attached.


Thanks

Been using the DT85 for abut 2yrs. 2 weeks ago I updated the firmware from 9.08 to 9.16. Now all mimics work except Charts. I can set up the chart but no data is displayed. Now sure what else to try?

I have tried to set up a daily schedule to save newly acquired data to a USB memory stick.

I set this up in dEX configuration builder by adding a new schedule to run every day at midnight, then added a manual channel with the command

COPYD dest=A: format=csv archive=N src=BD start=new;

If I issue this command in the command window, it successfully saved data to the USB device.

Wh

Dear all,

We use a device from http://www.soilmoisture.com/TDR-Equipment/ (all 3 types) for mesurement 16 channels of water content with time domain reflectometrie system.
How can I control and readout this with a dEX - script at DT85.

Please help me

Hello,

We can't read the legacy configuration back in the data-logger. In order to gain storage space for the installation files we deleted the job, data, alarms, configuration out of the B drive.

Should we create a new job first? Or should we go back to version 9.08 and forget about the new version (where can we get version 9.08 from)? Re-make the configuration which would take us a lot

Some questions about security settings on the DT85:

Are the firmware security settings documented in Part Q of the manual (PROFILE AUTHENTICATION ENABLED, USER, SIGNOFF, SIGNON, WHO) are the same as those set in dEX security?

Can more than one user be logged on at once (e.g. of the DT85 is accessed via an internet connection)? If not, what will a user see if they try and access the DT85 e

Hi,

We have always connected our DT85 (V6.22) to PC with DeTransfer or DeLogger using USB successfully. But now it can not be connected, because there has no USB Serial Port display in the Windows Device Manager when insert the USB of logger to the PC.

We tried to change the PC and USB, restart the logger, but still no any response received.

However,when we changed to use a USB to RS

Hello I have a DT85 which will not sleep. It has external power and I have set registers P15=3 and P17=300 but it stays on between 4 hour uploads. I see that if there incomplete jobs entered it will not sleep. How would I see these and how to delete these? Is there another reason for it not going to sleep
I have an Identical machine which is sleeping no problem.
Program as follows any help

I want to run my DT85 from a USB stick. My understanding is that this can be done by porting your program to a file called oninsert.dxc.

I am currently using DeLogger4 to create my job which I can run when connected via USB cable. For the life of me I can't find a way to create an oninsert.dxc file with this program.

Can DeLogger create this file or should I be using a different program?

Hi I have a DT85 which i am logging some temperatures & solar radiance.

I have 3 schedules the first is a standard logging schedule at 15 minutes it simply logs the radiance and temperatures.
the second is the same channel setup except I am logging every second and using CV's to accumulate the total radiance.

The third schedule i wish to setup to log the following.
the average &

Our DT85 inexplicably neglected to log 7 minutes of data on a minute schedule. The last successful data record logged before the data loss had a time stamp of 12:00(noon). I glanced through the service log to see if there was an error around the time of the data loss and I found this:

2014/09/24,12:01:24

An error occurred at buf.c:19
Task: HTTP 2

Current task : HTTP 2
Error loc

Occasionally our DT85 will reset and we'll lose about 7 minutes of data. This shows up on the event log at the time of the data loss:

EVENT ,2014/10/16,12:27:21,0.755615,"No HTTP listener running: restarting"
EVENT ,2014/10/16,12:27:24,0.937377,"Reset 9.10.4890 PLL/WDOG/DEBUG (c860400d)"

I was told that the 9.14 firmware was buggy, therefore I downgraded the firmware to 9.10 thinking t

As part of my student project I'm trying to establish a communication between the DataTaker DT85 and Swegon modbus gateway connected to CASA
ventilation unit (this is the first time I'm working both with modbus protocol and DataTaker). The aim is to have the values measured by the sensors in the unit also logged by the data logger. However, I receive the error E124.

The slave device is pow

Hello -

I am having trouble upgrading the software on a DT85 (I believe series 1). S/N 083710

I normally use DeTransfer for a newer logger I have but the "upgrade firmware" function is grayed out when I connect.

I tried two different USB sticks - one was an 8 Gig which I understand is too big. I also tried a freshly formatted FAT32 256meg stick and it didn't work either. It just reads

I have some T/RH sensors (Precon HS-2000V) and want to connect them to the DT 85. But I don't know how to connect the four wires.

Hi Support,

I am trying to send the follow data to the RS485 port in HEX: 68 04 00 04 08 by sending \104\04\00\04\08
however it appears that only 68 04 04 08 is sent, the 0x00 in the middle was not sent.

Is there a workaround for this?

Thanks very much for the help

BR
Eric

Hi,

I am using the +5V output to power a humidity sensor, I have used the command +5VSW=1 and set the logger up so that the 12V subsystem is continuously powered. However when I run the logger, the +5V works for short scan times (5secs) but for 15min scans the +5V does not switch on and so the sensor gives a bad reading.

Does whether having the USB connected affect whether the +5V SW is

Hi

I am looking to read PT100 sensors and digital inputs from a novus digiral module http://www.novus.com.br/site/default.asp?TroncoID=621808&SecaoID=819191&SubsecaoID=0&Template=../catalogos/layout_produto.asp&ProdutoID=748482

Can you confirm how this can be done with the dt85 sensor port I was looking at something like 1MODBUS(AD2,R1:1,=12CV) to read the digital state a