Hi All,

I am working in a project where we are using the DT 80 series 3 with strain gauge application. The resistance according the supplier is 350.4 Ohms ...Bridge connection has been done with DT 80 as per the drawing...Web interface has been established B/W laptop and DT 80 for configuration....Basic configuration have been done and this i configured as BGI (current excitation and arm resi

Hi,
I'd like to know can I put my data TAKER which using generic gsm modem to sending a sms within specific time.
For example i install the program 10:02 am but i need the data taker to hold the program until 10:59am.

Can you help me?
Thank you very much with best regards,
Tommy

Hello!

I have some questions about this topic!

I know that when power fails, internal battery fails and lithium battery fails, the clock/calendar is reset to 1989, and loses some memory settings. My question is which ones?

I Know that in DT800 it loses is mains frequency P11, date format P31 and time format P39. I do not know if it is the same in the DT80.

I have firmware 9.14.

I am using the dEX configurator with dataTaker DT80M firmware version 9.08.

When i set a key to run a job from the manual command windows in "monitor the logger" with the two commands profile function F1_label=test and profile function F1_command=runjob"test" the function key n.1 works but if i configure the n.1 key through the configuration logger page with the graphical setting keypad funct

I am using the dEX configurator with dataTaker DT80M firmware version 9.08.

I want to create and configure more than a job with the dEX option "configure the logger".
When I select configure the logger the dEX creates a new job called "CONFIG" and if I save it, it overwrites the previous job i had configured and saved which has different schedules and channels.

My question is if there

Hello,

I am reading Digital Input 1, where a switch is connected, with 1DS command. I would like to convert the 0 (closed contact) and 1 (open contact) status to 0(open contact) and 5 (closed contact).

Thank you,

Richard

Hello All,

I have a problem in collecting and transmitting Rainfall data using RF module . And I really need your help.

Rainfall station transmit data via RF (because this place is not 3G, Ethernet) to Repeater Stations ( long range: Maximum of 30 km over mountainous terrain). And from Repeat Stations transmit data via RF to System Center Station (long range: 30 km).
Which RF module is c

Hi,

I've got a situation with my dataTaker program. I'm using the DataTaker to store the values of holes being dug into the ground. I've programmed it to unload data into a .csv file every time a hole is dug, with the file name being the coordinate of the holes. So, I would have files such as XX1YY1.csv, XX2YY1.csv, etc. being created in the 'b:\' drive. I'm able to access it using the FTP se

Hi,

i connected as per attach picture and my program is [BEGIN S1=0,15"m" RA2S 1#L(S1) END]. the return value is 'UnderRange'
sensor output is 4~20mA. we have connected with multi meter(amp reading) and given success result.



Please advise

Regards,
Rosli

Hi,

in Data Taker, do we have string manipulation ?

Example syntax:
IF(2$=="test"){7CV=2CV}

But that syntax is invalid. Any suggestion ?

Hi,
After switch off the power supply, current counter at HSC will be reset to 0.

How can i retrieve back the last value of HSC after data taker power on ? Means that the last counter of HSC will restore back.

Thank you

Hi,
I'm trying to convert one of the serial command to the data taker command.
Kindly advise if my translation command is wrong.

Serial Command is :-
AT+CMGS=<+60174365685><CR><message><CTRL-Z>

If convert it to data taker command, it should be :-
2SERIAL("{AT+CMGS=+60174365685^M}{TESTING^Z}")

Is it correct ?

Regards,
WanRosli

Hi,

we have an DT80 in the outback. 2 times in 3 month we had an failure (see subject). The logger send normally every day data to ftp-server and weekly an email without problems. Firmware is 9.18.6291. Have anyone the same problem or a suggestion? After re-input via keyboard the communication works again or we restarting the system.

Thanks Volker

Hi,

I've found when opening files from logger that some fields appear to have reset to default such as:

the time i had set to trigger an ftp upload resets to 00:00

the drop down box beside the Send type changes from "immediately via modem" to Ethernet, I've noticed this also happens just by changing tabs

also when viewing the csv created by the logger there is a column titled TZ w

Hello all

I have a DT80M that we are using to monitor a shipment during road transport. We take a number of readings such as GPS data, A couple of pressure readings, Temperature, humidity, Accelerometer and a battery voltage.

I am having troubles with the GPS data. It only takes the first reading when the Datataker is turned on and either never tries again or doesn't save the changes in t

Hi

I have a Datataker that is occasionally losing its Modbus settings. it last lost t settings on the 24th and had the following in the event log.
the second and 3rd line are what I am most interested in as I havent seen them before.

EVENT ,2016/02/24,05:28:27,0.693115,"SESSION: Failed [Network check] - will retry"
EVENT ,2016/02/24,05:29:11,0.575561,"Peripheral prepared to hard r

Hello,

I'm new to DataTaker programming and need some help with the AND operator:
The next line gives me an error and I can not figure out why:
IF((599CV==93)and(600CV==0)){600CV=1;XB}

Just testing to expressions and if result of both is "1": set 600CV to 1 and execute XB.

Thanks in advance.

Hello,

Have a question regarding logged data.
If I look at the csv file then it seems that sometimes data is shown with different numbers of digits in the same column while the real value does not change.

Please have a look at the attached document. For example the MS Battery Voltage column. Sometimes the data is shown with 5 digits then with 8 digits. While the sampled real value does

Hi there,

it is possible to send the event- and error logs per Email, triggered by a regular job schedule? Our system sends the measurement data on a regular basis via email, and it would be nice to have the logs available, too, in case something brakes. As far as I understood from the manual, the COPY command can only upload to an ftp server. Do you have any suggestions?

Thanks for your

Hi
I have programmed a dt80m and I have various alarms which when activated are to send out an sms to 3 different numbers. within the output of alarm I have added 3 separate sms one for each mobile number as the sms output has provision for only one number. however when the alarm becomes true the dt80m attempts to send the 3 sms alerts but generally will get one out1 or 2 and sometime none as