Hello Everybody,

I have a problem about configuring DDNS for DataTaker DT80M:

I am using a SIM which support 3G (Made by Swisscom in Switzerland). This SIM has been active and it has “IP public address”. It change IP address after the modem DT80M is restarted.


I create an account with DDNS service provider: no-ip.com.


I create a domain name for the logger, and attac

Hi

We have just taken delivery of a DT80M to use for collecting data when brake testing. To give us the vehicle speed we have obtained a CAN bus interface which gives us a pulse on a 12V signal that equates to 1Hz = 1 mph. I am stuggling to understand how I can read this signal to calculate the vehicle speed. Has anyone got any suggestions? I have tried the analogue frequency method and the

Hi,

I am a student researcher. We have DT80M model. We need to connect a controller to the DT80M through a rs232 port and need to view the information in PC. Since DT80M doesn't have a rs232 port.

Can i convert the RS232 to RS485 and then connect it to PC for retrieving information? Is it even possible?

Thank you for your support

Hello everybody

Yesterday I encountered a problem with the DT80M.

We made a wind speed and direction measurement system (two sensors from a German company).

The plant is located in the Lucomagno pass here in Ticino. The temperatures these days were always below 0 (up to about -26 °).

Two days ago the DT80M no longer sent the data to our server, and yesterday, on the spot, I sa

Greetings,

today we found that our data logger became unresponsive (display interface and modem/Ethernet connections not working) and stopped retrieving/sending data after just a day of testing in the office, the logger was sending data through the modem.
This has happened before with some of our loggers and we had to unplug the power supply to get it working again, after the occurrence we

Hi,

following problem arises due to my first stept in datataker's world:

I want to send daily CSV-Data (0-24h) at 6:00 to my ftp-server (schedule "C" will send it at 0:00). how to implement an offset (without changing timezone!)?

Code of the Job:

BEGIN"CoRiIMG"

RA"Measuring"("b:",ALARMS:OV:100KB:W60,DATA:OV:1MB)10S
LOGONA
4SDI12("Wind-Dir_AVE~Deg",LM,AD0,R101,CM)
...

Hi All,

Long time since I've had anything to do with DT's (5 years) but am now getting itchy feet and looking to start some remote logging in the future.

I'm interested in using GPRS in order to have continuous data (every 1 to 10 minutes) sent to a receive PC Server from a network of loggers - most likely DT82EM.

Has anyone had success using GPRS? I did a search and came up empty.

Hi,
I'm integrating the Pulsar Microflow (modbus version) [https://www.pulsar-pm.com/Portals/0/docs/manuals/MicroFlow-Manual-1-ed-R3.pdf ] and it seems the manual fails to mention serial howto.
The sensor is address 10 and I need the integer part of the velocity [register 20] and the fraction part [register 21]

All the service parameters are not necessary to log, I can access with propr

I have created an oninsert.dxc file that resides on the USB drive that is used to unload the data from site, the files consists of the following:
H SATTN;
COPYD Dest=A: format=csv;
CATTN G
and has worked well until the recent firmware upgrade. Now I get a COPY -> USB Failed(-16), can anyone shed some light on the subject.

Good day,

DT82E with beta firmware has been working well last 3 years(ignore SDI12 events, it's problems with flowmeter)
But Logger have had problems with ethernet connection last 6-7 months. It lose connection once or twice a week(Shedules are working without problems)
All is ok after Hardware Reboot(Power reset)

I didn't find any ways for automatic reestablishment of ethernet conn

We have three DT82E-2. Two run on 8.08.001. One runs on 8.06.001. All three show allow_anonymous to be "NO" in the profile thru dEX. But only the one running on 8.06.001 disabled anonymous FTP. Anyone aware of that? Any idea to make the other two behave the same?

SW Exception started happening repeatedly on my unit after a recent power outage. Please review attachment for a snapshot of the event log around that time period. What can I do to fix it?



Thanks.

Hi there,

we have a dt82e as weather station data logger, the station has a solar panel , charger controller and a 12V 7Ah battery.

after some electrical failure (we still working on to find the cause of the problem (probably the charger controller)), the datalogger stops and enter in continuously reset loop. after holding the OK/Edit, it enters in bootstrap mode for 15s but after timeout

Hallo every body, please help
I have DT82E
with thies clima sensor product :

a. WIND TRANSMITTER CLASIC (4.3303.22.641)
b. WIND DIRECTION TRAN (4.3125.32.041)
c. Hygro-THERMO TRANSMITTER (1.1005.54.241)
d. BARO TRANSMITTER (3.1157.10.100)

How to connect the sensor and how to program? ( WS- knot; WD-deg ; Temp - c ; Hum-%; Press - Hpa)
I convert 232 serial output with RS232

Hi,
I'm using a solar powered DT82E with an external GPRS router to transmitt data via FTP once per day.
To save power I switch on the modem with 1RELAY=1 a few minutes before starting the COPYD command.
The relay should be switched off after data are transmitted successfully to the server.

How can I check if the FTP data queue is empty?
SESSION LIST command shows the state of the

I have 100 DataTaker 82E's installed. Each is monitoring a voltage that is within the 30 V range associated with 2HV. On quite a few systems everything is entirely consistent but in some of them there is an occasional overrange indication which would indicate a voltage in excess of 30 V. Is there any possibility that this error is generated by an issue with the autoranging rather than the input v

Hello Everybody,

I have a sensor which is porduced by Monitor sensor. You can see at link: http://monitorsensors.com/upload/PDF/AN.pdf
With this sensor is: 3 wire

Red: supply power 6-28V
-White: common
-Black: data
I use external power 12V to "RED"
Channel 2 analog: +/-
My code:
BEGIN
S1=0.1,40,2,10
RA1M LOGONA
2F(S1)
END

or

BEGIN
S1=0.1,40,0,2500
RA1M LOG

I have a 1 min schedule that prepares data. 5 seconds after the schedule a poll unload is executed. The response takes minutes. this may have to do with configuration of the communications. I have 7 sites,6 work without error. The other site has consistent unload delays. The source is the same. Ideas?

Hello All,

I used to work Ethernet Email for DataTaker Model 80. It is successfull. But i have a this problem with DT 82E serial 2. DT 82E can't work via Ethernet Email. ( but FTP is OK)
I don't know why.

Please help me
Thank you very much

Hello Everybody,

I am looking for some sensor with DataTaker for my observation system. They are Thermometer sensor, Visibility sensor, Wind sensor, rain and precipitation sensor. I see them at Vaisala

http://www.vaisala.com/en/products/rainandprecipitationsensors/Pages/DRD11A.aspx
http://www.vaisala.com/en/products/visibilitysensors/Pages/PWD50.aspx
http://www.vaisala.com/en/produ