G'day Team,

Hope you can give me a quick pointer.
I have a serial scale sensor sending me back a weight in format "ST,GS 2.450kg"
So I am using the serial expression builder in an attempt to get the 2.45 out.

1SERIAL(RS232,"\eST,GS%f[5CV]kg")
Works like a charm getting me 2.5 (seems to round the decimal part up)

So I am trying a formatted float
1SERIAL(RS232,"\eST,GS%5.3f[

We have a logger that we connect to with a radio modem we randomly get Exception 200 error and the logger resets.

dataTaker 82 Version 9.14
Initializing...Done.
Warning: abnormal firmware reset - type UERRLOG for details
DT82>
2016/10/27,01:43:16

An error occurred at dcchntab.c:4578 4
Task: Command Processor

Current task : Command Processor
Error location : 0002

Dear Roger,

When my DT85GM upgraded firmware 9.08,why the connection of modem test failed in SIM access?

The connection of modem was normal before upgraded.

And when I use USB port to connecting to the web interface,some function can't working.

Dear Roger,

1.One DT85GM to Measurement 14 Resistance , 8 Voltage , 1 Current , 4 Current Bridge.FTP data via ethernet.
2.Trigger in every 5 minutes.
3.Everything is normal.

When I add one CEM20 and move 4 original Current Bridge to CEM20.The DT85GM will Low Power forced sleep.
How can I solve it?

Hello,
We have a DT85M.

We have a job which sends every 24h a SMTP email.
As the carrier is T-mobile, we set in the code APN as following:
PROFILE MODEM APN="epc.tmobile.com"

We want to use the same job but using a SIM from another carrier, AT&T.
The phone subscription is data only (we cannot send text or call).
The only modification in the code should be the APN, to co

Hi everyone

It´s the first time I use a datataker and i have already a problem.
I need to change the serial sensor port speed during logging because i have to communicate with two different devices that have 2 different speed. I tried in a manual channel something like this:

ps=1200
1SERIAL("{\002}")
ps=2400
1SERIAL("{\002}")

I tried many variants with delay and wai

When ever I Run a VFD or a Welder near the unit I experience noise. Has anybody experienced this, and or know how to fix it?

Hello,

We work with a DT85M, firmware v9.16, used to send emails with SMTP.

I used dEX to configure the system:
-- Modem email --
From Name: daq
email: xxxxxx@gmx.com
SMTP port: 25
SMTP server: smtp.gmx.com ( I also tried mail.gmx.com)
Username: xxxxxx@gmx.com
Password: xxxxxx
-- Modem --
APN (manual): epc.tmobile.com (the carrier is T-mobile)
Username: [blan

Dear Sir,

I have an unused logger left for about six months, when powering it back on, the firmware seems to have corrupted / lost.
I was trying reload the firmware by using the DeTransfer program / a USB drive without success.

The logger ignores my USB drive (FAT) and simply return to flashing of all of the 4 lights when i press the ok/edit button.

for RS232 / USB cable, I could

Dear Roger,

I am deploying a few DT85GM in Hong Kong, and I am experiencing "SIM Problem" with simcards from Smartone HK.

I first tested the DT85GM with my own personal simcard (PCCW HK) and it worked smoothly, but when Smartone HK gave me 5 brand new sims they all have "sim problem" when the modem was starting up.
I tested the 5 sims in my phone and they appeared to work without probl

Using dEX, how does one programming the channels for a connected CEM20 module? Is this even possible?

My DT85 is scanning data every 15s and logging the average of 4 readings every minute.
At 0758 on 5th May, after weeks of working satisfactorily, it missed a reading, and the following reading at 0759 was corrupt.
The Service log is attached.
How do I stop this happening again?

Hello,

I have a DT85M with V9.16 that will run for 10-30 secs, shut itself off, and then restart with a "Power Loss" message. Whether you clear the "Attn" LED or not, it will sample for a few secs and then repeat the process over again continuously until power is removed. After one of the restarts, the unit displayed the "SW Exception" error. This set up worked a few weeks ago. The unit will

Hi All,

I am currently in the process of connecting up 20 strain gauges to a CEM20. In order to help reduce electrostatically induce noise, which can be a problem with my setup, I need to ground all of the shields at the Data Taker end. Although there is an analogue ground connection on the DT85, I do not see one on the CEM20. I could connect all of the shields up to the DT85, however this wi

HI

I am doing a job at the moment, where we require 3 remote dataloggers, to provide continuous live data. I am wondering how do I use the internal modem as the modbus interface between the DT82EM and the SCADA/PLC,

I understand the DT82EM will have to have a fixed I.P. address attached to it, or else go in through a Dynamic DNS, but what i am wondering is,

Is the logger automatical

Hello Everybody,

I have a problem about configuring DDNS for DataTaker DT82EM

I am using a SIM which support 3G (Made by Viettel in VietNam). This SIM has been active and it has “IP public address”. It change IP address after the modem DT8x is restarted.
I create an account (nth_ngo) with DDNS service provider: no-ip.com.
Host by Domain: huynhdang.zapto.org
+IP/URL: 171.243.

Hello Everybody,

I am using deX to configure to DT82EM.
My SIM PIN is " 0000". BUT When i type this pin to deX and save to logger, the deX only shows "0". So the configuration is wrong
I have change SIM PIN "0000" to " 1234" . The configuration is OK.
Could you tell me about this problem ?

Thank you very much

thuyvan

How can i change (or even see) the auth method used by datataker to login on gsm/3g network? There's a PAP and CHAP method's and sometimes is mandatory to setup a specific method to work properly...

Hello All,

I am finding a sensor which measure Flow Rate, Water Velocity and it have to connect to DT82EM via SDI-12 interface. It is Ultrasonic Doppler sensor.

If anybody knows that sensor (it have to connect to DT82EM), tell me about that please.

Thank you very much

vinhquyen

Hi,

I am new to DT82EM so apologies if this is an obvious question.

I would like to set a trigger that is set when an SMS is received at the internal modem of the DT82EM. Is this possible?

I had a look at the FAQ, forum, technical notes, etc but have not found anything relevant.

Thank you for your help.

Regards,

Jhon