Hi,

I have been trying to use dex-2 to connect to our DT85Ms. I am using a USB cable straight into the device.

When I try to connect, using the port and IP address from DtUSB, it will not find the device. Looking at the code found in the "Development Tools", it keeps throwing back a 403 error. Specifically:

"Failed to load resource: the server responded with a status of 403 (Forbi

I am monitoring an air conditioning system for occasional trips of the compressor overload. While monitoring all the usual things like temperatures and pressures and compressor current at 30 second intervals, I also want to monitor the three compressor current transducers "as fast as possible" for 2 seconds following the contactor closure. I've looked at scanning fast in the manual (under "Contin

Is there any way to input a value into a CV variable via the front screen display and function buttons on a DT85?

Hi, I use DT80W-S4 to measure analog (4-20mA) Water Level Sensor. When I calculate the mA that DataTaker measure is different from what the sensor output mA. How to make DT measure the same mA value as what sensor output? I did adjust the ohm of the 100ohm resistor but the resistor value only can be input round number.

Good morning,

it was setup the DT80 is now saying offline and the comms light is yellow.

Just wondering if this is the same issue.
"67

Alarm action will cause an error in the channel thus no editing is possible."

If so what is the fix?

Hello i habe trouble with my Programm on my DT85M
Actually it is my first Project with a Datataker

I need to read 200 soil moisture sensors.
Each sensor has 4 variables to measure
175 of them are with modbus where i have to recalculate 2 of the values
25 are with SDI12
The Sensors work and i can communicate with all of them.
So i have 1150 values to measure with this sensor

Hi was wondering how you can save the configuration to disk so it can be accessed at anytime (as backup) or downloaded in the datataker.

Refer to page 117 in the user manual for the old flash version.

Hi

I need advise on connecting the pulse output from Burkert SE35 Flow Transmitter to counter input of DT80 please.
Link to the transmitter docs https://www.burkert.co.nz/en/type/SE35

Thanks
Bill

Hello i am new with Datataker

I just installed dex 2.1.18 but it does not find my DT85M.
With firefox and the Flash player i can programm and find the Logger, but it works awfully slow.

The logger is connected via USB.
dtUSB shows the loggers IP.

I would be very pleased if somebody can give me a hint what's wrong with my setup.

I use Windows 10 Logger firmware version is 9.2

Hi,

Can the Ethernet Port on the DT85 be used to send a Modbus command to a TCP/IP Modbus Server Device (e.g. Sensor configured as TCP/IP Modbus Server) as well as receive a Modbus command from the TCP/IP Modbus Client Device (e.g. SCADA) simultaneously?

Thanks.
AJ

Hi,

I am trying to configure a sensor to record data using a DT82I.

I have the sensor connected to the green serial connector on the front of the logger. The sensor communicates using MODBUS.

I am attempting to use the following code to log the temperature data from the sensor as 1CV:

1MODBUS(AD1,R4:15,MBF,=1CV)

I keep getting an error code "E122 - Command incompatible with

hi all,
I am having difficulty being able to log onto the Data Taker I have, I have downloaded the dEX2 and the DtUsb software. The computer sees the Data Taker as it shows up in the devices tree, and when I connect with the USB I can see the IP. 127.1.1.1, but again I am unable to log into the Data Taker .

Does anyone have any solutions?

Many thanks
Sam

Hi! Noob here. I'm using my DT80 for simple temperature measurements, succesfully getting two simultaneous signals in ports 1 & 2. My issue is that I want to trigger logging schedules, i.e. by having a circuit in the upper left block (the 1D 2D...GND block) that will start the logging. How would i code this in the interface?

Thanks for any help, and sorry if this is unclear! Not fluent i

When i use the run wizard to set my mains frequency to 60HZ and temperature units to Fahrenheit , I continue to the end where i click on submit. When i collect my data it is in Celsius and when i check logger regional settings i see 50HZ and Celsius. I am using a DT85 with v9.22 firmware.

RESISTANCE NOT SAME AS MULTI-METER

Hi i have just purchased the series 4 DataTaker DT80 and CEM20 expansion modules.
ill keep it simple and quick, i have been testing with 390 Ohm 1% resister (same resister) and compared it with a multimeter.
results:

CEM20#2 = 394.2 Ohm's
CEM20#1 = 394.0 Ohm's
DataTaker = 391.6 Ohm's
Multi meter = 388.4 Ohm's

Is there something i can d

Hello,
We have furnace controller that uses a type C thermocouple to report temperature. I wanted to use a 4-20ma output from the controller and use it as an input for the datataker and have it convert to temperature. I know the datataker can convert mV to temperature, but what about mA? Is this possible?

I have a DataTaker DT80 that was coded using a different coding software other than dEX. If the code makes references to 1CV, 2CV etc., that would be decimal addresses of 31001, 31002 etc. correct?

Hi, i was trying different schedule triggers and i went from 100T to 50T and to 5T. At this point the data taker command window froze. I rebooted the web based command window and the i did delalljobs.
The data taker restarted and then an error pn the display of the data taker came ok, which is SW exception.
Though it says no current job i can't schedule another one because it says the un

Hi all,
I have what I thought was an extraordinarily simple application. I am using a DT85 to record 32 thermocouple measurements at 5 minute intervals. It is so simple I chose to make the configuration file on dEX-2 on the desktop. My problem is, when I save the configuration to the logger it scans and saves just fine but the schedule appears corrupt on dEX-2 (After channel 19, every even-nu

Hello,
i wish to count the Sunshine duration with the DT82I-3 over the digital input.
The Senser does have a Digital Output. Sun =1 otherwise =0
Now i wish to Count the total Time of the sunshine duration each day and log to CSV. This means. The Counter Starts each Midnight with : 0h 0m 0s and count the Time the digital input does have the input status "1"(high).

How can i solve thi