Support Forums
Command Window Doesn't enable

Hi Roger

Thank you for the tip, however with those settings I still cannot get it to accept the program. Would there be any difference between using the desktop version of deX or the deX from the logger?

Regards
Andrew

Hi Roger Thank you for the tip, however with those settings I still cannot get it to accept the program. Would there be any difference between using the desktop version of deX or the deX from the logger? Regards Andrew

Hi Andrew

dEX is a web based application and there for requires a TCP/ip connection.

Once you have loaded the dEX config you can then send the commands to start / stop etc.

If you write your config in the dataTaker language or extract the dataTaker code from you dEX configuration then you don't need a TCP/ip connection to config you logger.

Cheers

Roger

Hi Andrew dEX is a web based application and there for requires a TCP/ip connection. Once you have loaded the dEX config you can then send the commands to start / stop etc. If you write your config in the dataTaker language or extract the dataTaker code from you dEX configuration then you don't need a TCP/ip connection to config you logger. Cheers Roger

Hi Andrew,

Can you please check the logger command language?
That error "at line 27 col 56 [MB]SERIAL <err>'P141'" might also related to the missing number 3 for 3SERIAL.

If that is true, please try to upgrade the logger firmware.

Notes:
Incompatible port has been addressed by Roger.

Best regards,
Rudy Gunawan

Hi Andrew, Can you please check the logger command language? That error &quot;at line 27 col 56 [MB]SERIAL &lt;err&gt;&#039;P141&#039;&quot; might also related to the missing number 3 for 3SERIAL. If that is true, please try to upgrade the logger firmware. Notes: Incompatible port has been addressed by Roger. Best regards, Rudy Gunawan

Hi Rudy

The missing "3" is probably a transcription error, as I was using dex I don't think it could have been omitted. I am using a TCP/IP socket to connect to the logger. However I am using the desktop version of dex rather than the dex pages stored on the logger (it takes several minutes for the web page to load). Does this make a difference? If so it is only when trying set up this particular function. If I set the schedule to run continuously or on a digital input then can upload the program without difficulty.

Regards
Andrew

Hi Rudy The missing &quot;3&quot; is probably a transcription error, as I was using dex I don&#039;t think it could have been omitted. I am using a TCP/IP socket to connect to the logger. However I am using the desktop version of dex rather than the dex pages stored on the logger (it takes several minutes for the web page to load). Does this make a difference? If so it is only when trying set up this particular function. If I set the schedule to run continuously or on a digital input then can upload the program without difficulty. Regards Andrew

Hi Roger, Rudy

Does the image below - extracted from the manual - mean that I cannot send a serial command via USB port to trigger a schedule?

5cb2bed8d1e67

Regards
Andrew

Hi Roger, Rudy Does the image below - extracted from the manual - mean that I cannot send a serial command via USB port to trigger a schedule? ![5cb2bed8d1e67](serve/attachment&amp;path=5cb2bed8d1e67) Regards Andrew

Good morning Andrew,

Yes you can trigger on serial data from the USB port
1Serial is the serial sensor port.
2serial is the RS232 host port.
3Serial is the USBhost port.
4Serial is the TCP/ip port.

Cheers
Roger

Good morning Andrew, Yes you can trigger on serial data from the USB port 1Serial is the serial sensor port. 2serial is the RS232 host port. 3Serial is the USBhost port. 4Serial is the TCP/ip port. Cheers Roger

Hi Roger

Thank you for the additional information. However I still cannot get the logger to accept my program I still get the configuration error when trying to load the program from dEX.

Regards
Andrew

Hi Roger Thank you for the additional information. However I still cannot get the logger to accept my program I still get the configuration error when trying to load the program from dEX. Regards Andrew

Hi Andrew,

Did you receive the same error? If yes, please use manual channel to address 3SERIAL.

Best regards,
Rudy Gunawan

Hi Andrew, Did you receive the same error? If yes, please use manual channel to address 3SERIAL. Best regards, Rudy Gunawan
12
266
27
3
live preview
enter atleast 10 characters
WARNING: You mentioned %MENTIONS%, but they cannot see this message and will not be notified
Saving...
Saved
With selected deselect posts show selected posts
All posts under this topic will be deleted ?
Cancel
Delete
Pending draft ... Click to resume editing
Discard draft