Hi All experts,

I collect data using all channels, 7 temperature sensors, 7 pressure sensors, 2 digital input, frequency etc.

When I open DEX2, I cannot view the data in real time including gauge pressure.

Is there a faster connection method instead of Ethernet cable?

Datataker stucks when I open the application.

I can download the data at the end of the day, but I want to

Based on the value read from a thermister I wish to activate a relay to continue a heater or turn it off until it drops below a set value. Here is the code that I thought would work based on the manual but it fails to compile.

BEGIN"config"
'Generated by new dEX-2
password=""

RA"Schedule_B"("b:",ALARMS:OV:100KB:W60,DATA:OV:1MB)2S
LOGONA 5R(II,2W,"Resistance~Ohms",=10

My DT80 Series 2 (Firmware 9.2) has been chugging away logging local weather and other farm data for the best part of 2 decades. No complaints about the durability!
I am now tring to add a Modbus Chinese soil moisture probe, and doing initial command line tests to work past the lack of functional documentation...
My first mystery is that the DT80 doesn't appear to care if the probe is conne

I have 3 E&H Promag400 flow meters that I want to connect to a single DT82I. All the inputs on the DT82I are exhausted so I am stuck with the high speed counter inputs 1C, 2C, 3C and 4C.

I have been reading through all the manuals to understand how I should wire up the flow meter frequency output terminals (24+ and 25-) to the DT82I. The flow meter output terminals are designated as pass

Hi, I I've just been given a DT85 for my work. Looks brand new but I think it is an older model. I cannot seem to connect to it. The IP address changes in accordance with whether I connect directly to the computer to to the network using an ethernet cable, but it stays stubbornly offline, and the console shows Error 404 as it tries to connect. I have opened Port 80 for inbound and outbound but st

Hi,

We recently purchased a DT80 Series 4. I've noticed that there is no connectivity between the ground terminals, including between digital grounds and analogue ground. When I enable the 12V output, I cannot see a voltage drop between the 12V output and digital grounds. However, I can see an 11.5V difference between the housing ground (the screw on the side of the DT80 housing with a ground

Hi,

I am running a job with 4 schedules, and while this job is running I would like to update one of the variable K-factor in one of the schedules.

CALC("Kfac~Kfac",=1011CV,LM)=20.104

How can I do it over telnet session while program is running?
I could set it and restart the program if it needs restarting.

Regards
Konrad

Good afternoon, I and my company "AVIPE" are having some problems with our DT80 Series 1 I believe.

What he problem is:
We programmed it to have the function, date and time.
But before that we had made it so it Only had the date and time (accidentally).

We programmed it and went to go eat, later (1-3 hours) we checked back on the DT80 and it REVERTED back to only having date and tim

I'm trying to setup a DT80 that my company has had on a shelf for likely 6-8 years. In order tot ry and use the device using the dEX-2 software I determined I needed to update the firmware. However I cannot use the browser interface due to the lack of flash. I opted to use the USB update option. However it sat stating it was processing "oninsert.dxc" overnight with no change. Is that expected if

Hi,


We have some field instrument signals wired to Yokogawa DCS and want to push those values via Modbus to DT85 and then DT85 will upload on an FTP server to prevent DCS exposure to outside world from Cyber Security perspective. Is it something that is possible using DT85 as a Master?


In some other DT85 we have hardwired signals connected to DT85 and CEM20 modules, data logger is uploa

Buenas noches, tengo dificultades para configurar por linea de comando el datalogger DT85G como MODBUS ESCLAVO por RS485.
He creado el siguiente programa que lee temperatura

BEGIN"DT85GGGG"

RS1S
RA"Programa_1"("b:",ALARMS:OV:100KB:W60,DATA:OV:1MB)5S
LOGONA

2*YS05("termi_2~degC",=1002CV)

4*YS05("termi_4~degC",=1004CV)
END

Ahora, como hago por linea de comando p

Dear All

My DT800 that was monitoring a weather station stops working.

https://datatakerforum.com/index.php?u=/topic/1127/post-4091&page=from_notify&nid=3991/#post-4147

I send it for repair in a representative and he said that equipment is obsolete, no replacement parts etc...

This equipment was buy many years ago and stay in the box for this years.

Recently I use it t

Hello,

How do I configure dEX-2 to talk to my DT85 over USB?
The serializer app finds the device and writes to it successfully, but how do setup the 'Add Device' screen in dEX-2?

DT85 series 4
9.22 FW
dEX-2 v2.1.25

Hi is there a way of having a mimic whereby you can input a value into a cv channel that can be used to change alarm values to avoid having to change values via the program config page as there is a number of alarms which makes it more difficult to config all in config section

Hi,

I would like to trigger DataLogger over telnet connection to start data capture, and after defined period of time 10 min for example, DataTaker should save this 10min period data back to ftp server for example.

Regards
Konrad

Hi,

I need to set up two PLCs to read data from DT85LM3-4 via Modbus TCP/IP. When both PLCs try to read data, only one works. Is it possible to set this up, or shall I try another solution?

Best regards,
Filip

Hi there,
I've got a DT85G series3 and a external 3G Modem onsite , it is logging data fine, but the communication is working temperamentally recently. There is 'SW exception' showing on LED. checked the event log, the logger is trying to send email which is not anticipated. below is part of the service data.
many thanks for your help.
Quan

EVENT ,2023/12/15,12:19:40,0.542602,"EM

Hello,

i use a DT85 to log meteorological data to an usb Stick.

At some point after around 2 months the DBD file seems to get corrupted somehow. dump_dbd and the logger itself cant convert it to csv.

I dont know the reason although i am suspecting an issue with the usb stick which i now changed.

But i still have the dbd file which maybe still contains some data.

From dump_dbd

I have remote access to a DT85 with S/N 106343 and firmware version 9.18. Due to flash expiry I can no longer access the web interface via a local raspberry pi, however I can access via FTP. My questions are:


What is the series of DT85 corresponding to this serial number?
How can I upgrade the firmware over FTP?

Thanks in advance.

Hello,

I want to use strain gauges on the DT85 and CEM20 device. The strain gauges we will use have a quarter bridge. Does the DT85 device and the CEM20 device have a wheatstone bridge? Or will we use resistors ourselves to make the rest of the devices a full bridge?