It seems the dEX-2 software can't compile dxc files containing the running average function. Is this a bug?
I've tried adding the RAV option to a thermocouple channel and I can't upload the program to my DT80 anymore, as it kept telling me compilation failure.

BEGIN"config"
'Generated by new dEX-2
password=""



RS1S

RA"Schedule_A"("b:",ALARMS:OV:100KB:W60,DATA:OV:1MB)5S
LOGONA

We are using DT605 and DT600 via RS232 com on very old computers and the original software.
Can you guide me how to upgrade the software and what will be the proper tool to convert the RS232 to USB?

Hello,

I am having trouble setting up a pressure transducer to the DataTaker DT80 series 4. Using dEX logger software 1.85.002 version.

Pressure sensor HT-SMH-10.0-0200000-BAR-(g)-U98F-22-M16
https://www.hydrotechnik.co.uk/sites/default/files/downloads/ht_smh.pdf
(The specifications are on 3rd page of that pdf)

What I have been doing is trying to use a current-loop with a 100 o

Just setting up a DT85 to read a Type K thermocouple.
The DT85 has been updated to v9.22 and I can see the relevant data via Dex-2 software.

However when I try to set up a guage in Dex-2 for the thermocouple, I'm unable to select the channel in the software.

What am I missing??

thanks
Greg

Hi

when I tried to add a new channel in my schedule, and then apply to logger, it didn’t get uploaded into my datalogger. Please advice as I cannot update the configuration.

thanks

Hello, I am trying to log the voltage current and power data from the m850 power meter via rs485 with a dt80 logger. I found some code examples and put the following code together. I have linked the manual with the modbus register list. Can any one say if this should work? Any Help most welcome

https://www.hobut.co.uk/wp-content/uploads/2022/02/M850-LTHN-RS-PO-User-manual-rev-4-SP-compresse

When running a job on our Data Taker the device gives the error "SW Exception". We are using the latest version of the firmware 9.22.9125

The event log contains the following message:

EVENT ,2023/08/15,00:49:01,0.139160,"Reset 9.22.9125 EXCEPTION (c8610007)"

And the error log contains the following message:

Exception 1c00 at 0x0011b348
SRR1=00009032 DSISR=00000003 DAR=040

I have DT 80. I want to connect load cell having 4 wire and 6 wire.
The colour for 4 wire load cell = red, white, black, green
The colour for 6 wire load cell = red, purple, green, yellow, black, brown.
How to connect load cell with DT 80 series 4 datataker.

I have been using Delogger4 for the Dt615 and delogger5 for the DT80 series for a good 3-5 years now with no problems.
Running Windows 10. All was fine up to a week ago.

The program loads, a Warning that the site database cannot be opened. Then closes program after you press ok.

Delogger5 works as per normal.

How can I fix this issue.

I uninstalled both Delogger5 and DeLogger4

Hello,
I am trying to install the Linux version of DEX2.0 on a centOS distribution.
However i am unable to complete the installation because of missing library and other ressources. I think the methods i am using are incomplete.

Could you provide the steps and terminal commands to use for the installation and the execution of DEX2?

Thanks.

How fast can you read thermocouple data? The manual says it is a sum of: Measurement time, processing time, communications time and logger preparation time.

But it does not provided values for all of these.

So how fast can you log analogue data without accuracy issues or channel ghosting? Is there a formula?

Dear all

We have a DT800 since many years and we use it a few times for temperature measurings
Now, i have a new chalenge to build a weather station with some sensores the we have in the lab

The sensors are:

SP Lite2 Pyranometer; sensitivity 68 uV/W.m-2
Thies anemometer 0.5-40m/s, a T351-TR Thermistor, a very old pluviometer that I will calibrate it.
And some k thermocouples

Hi

Can you recommend suitable main battery replacements for:

A) DT80
B) DT85

I know the DT80 is 1.2aH and the DT85 is 4aH but not sure of the physical sizes (The loggers are offshore so unable to look!)

Many thanks

Hello, I was trying to add a new channel to the current job on my DT80, and when I hit download, it wiped the job completely off the device. Is there a way to recover the job? Or do I have to start all over again?

When running a test on one of our DT80s, it sometimes fails on Vos 3W II. What does that mean and is it repairable?
Is there a list available of the test line items and what they represent?

VEXT 13.4 V
VBAT (6V) 6.50 V PASS
IBAT +4 mA PASS
VSYS 7.05 V PASS
VLITH (3.6V) 3.63 V PASS
VDD (3.3V)

Hi I have a DataTaker 605 Series 3 and I do not have the software CD is there somewhere online this can be found? it says in the manual the software is provided free with each unit.

Any help would be wonderful.

Thankyou

Dylan

Hi fellow users,

How can I execute an exponential function in a calculation dEX-2 / DT85?

Thanks in advance.

Regards,

Ferdi.

I have a DT80 connected to a CEM20 (id#2). The CEM20 has one 4 wire RTD and six 3-wire RTDs connected to it, reading in at about 1Hz.
They are Pt385 RTDs with 100 ohm resistance at 0C. I'm using the II parameter to excite at 2.5mA and, for the moment I am just trying to read ambient temperatures.

The 3 wire RTDs all read between 16 and 17C while the 4 wire reads 22C, when they should al

Hello,

i want to use a DT85 to query a Modbus RTU Sensor(Meier-NT Soitemperature Probe).

From my point of view i did all the necessary configuration but somehow i dont get any response from it.

Here is my Setup:

Hardware configuration:

A-Wire: TxZ
B-Wire: RTSy
Power: 12V Source
Ground: Common Ground with DGND
Software configuration:

[SERSEN_PORT]
*BPS = 19200
DATA_BIT

Hi, I have a project where I have 2 DT80GW units and I wish to connect the two together, one of which I want to send off data via a Email. I wish to use the integrated WiFi to connect the two together and then thinking of using a 4-G modem to send off data and alarms? Is it possible to link the units together this way?