rheem
posted Apr 18 '19 at 4:48 am
Hello,
I have searched high and low in the manual and FAQ without luck. The DT85 Series 2 has TWO power supply inputs for the switched excitation and shunt resistor. They are labeled exactly the same (EXT * and EXT #).
My question: Are these inputs tied together (is one EXT * electrically equivalent to the other)? Is one power input used for certain analog channels? If I am using switch
Cmin
posted Apr 18 '19 at 4:17 am
Hi all, hope that somebody can help me with this
I'm using analog sensors connected to a Voltage amplifier with a three conductor cable, one to signal out, one to ground and the third for power supply. The amplifier has an terminal to connect the power supply input +DC voltage (Vcc 5-24 VDC), but is not clear for me to which terminal in the datataker would correspond the power supply connecti
I hope everyone is doing well.
I have the DT85 series 3 dataTaker and I would like to hook up string pots to it for our testing lab. I have no experience with the data taker and would love any help anyone can provide
I've emailed tech support and they suggested that it might by a voltage divider pot but I'm sure that it reads resistance. I even placed a multi-meter across the green and
cbasler
posted Apr 18 '19 at 12:52 am
Hello,
I want to run the DT85 via USB, so therefore I need a USB-Driver. Unfortunately, the Driver on the page seems to be missing. Also, the dEX software platform, which I thought I could find is leading me to an "not found" page. Could you help me with that problems?
Greetings,
Clemens Basler
ITS
posted Apr 17 '19 at 11:59 pm
Hi
I have a dt85 whereby it is continually crashing and stops logging cannot be connected to, & front panel becomes non responsive.
the only way to get the logger back on line is to preform a reset and once this is done the logger reverts back to a much older date.
I have checked various possible causes but to no avail, I also have a UPS backup system on the logger but the problem p
Greg
posted Apr 18 '19 at 12:00 am
I've am attempting to connect to a new DT85 Series 4, but I'm having trouble connecting to it via USB and via Ethernet. My laptop has Windows 10 OS.
I have DeLogger, DTUSB and DeTransfer all installed. I have set Internet Explorer 11 as my default browser as that seems to be the preferred browser.
When I plug in via USB the dtUSB app starts in the background. When I open it up it looks li
I have a DT85 series 4 running v9.20
Whilst the logger is logging i want to unload a time frame of data. i try to connect via Ethernet and the address displayed on the LCD screen. the browser tries to go through its usual process but doesn't display the usual configure, monitor page?
i had to perform a hard reset which as a result looses all data stored.
i have the logger set for 5 s
For are thesis we are doing research to the hygrothermal behavior of wooden walls. To make measurements we are using the datataker dt85.
Our problem is now that the logger only gives the results for approximately 10 days, what's about 10 000 data, while in the manual of the datalogger is written that it has a memory for about 10 million data. Can we change anything to the setting so we can c
I have taken over a DT85 programmed by someone else. I have connected to the DT85. I need to change some IP addresses as a new router has been installed.
I can't open the command box to change IP addresses.
I am steep on the learning curve here!
I get the message on the attachment.
I have opened port 843, still no joy.
Any ideas?
RPE_GER
posted Apr 18 '19 at 12:09 am
Hello together,
I try to set the Date with the reading GPS Date but it doesn't work.
$GPRMC,094924.000,A,4856.8229,N,00824.6182,E,0.47,331.35,150118,,,A69
2SERIAL("\e\m[$GPRMC],%f,%1s,%f,%1s,%f,%1s,%f,%*f,%2d[420CV]%2d[421CV]%2d[422CV]",W)
420CV("Day") 'Show Day
421CV("Month") 'Show Month
422CV(W)=422CV+2000
422CV("Year") 'Show Year
Alarm(414CV==1)"Date update
I have to configure DT85G to measure Voltage in mili volt in one channel and current in micro ampere in second channel every second .
Please help me.
Thaar
posted Apr 18 '19 at 12:11 am
Welcome
We have DT85G recently, and we need to connect to it 3-wires LVDT of monitran company. we did several attempts of connection and all these gave an error reading.
The LVDT features are stroke 125 mm , supply voltage =9 to 24 Volts Dc(regulated) and its connection details are RED for supply volts DC , Blue for 0 volts DC and green for output(0-5).
With my regards
nn1in
posted Apr 17 '19 at 12:39 pm
Dear all,
I need to connect several Multi function Energy meter to DT85 using RS485.
I have never worked before with modbus /serial communication.
I checked manual and says need to set profile etc. But silly question, where do i put this code ? as i have always used deX for making program so it was pretty straight forward.
Should i use Detransfer to put command or can it be done
Hi,
I am using modbus tcp/ip for reading a multiple phase meter. Because I have to specify the IP-address of the meter the datataker is logging in each time I read the meter. Is there a way to avoid logging in each time when the datataker reads the meter?
Best Regards,
Friedrich Völlink
mpb
posted Apr 17 '19 at 12:42 pm
We've got a Dataker DT85 logger which scans data every 15s and logs the average of 4 readings every minute. The data is captured via DigiRails.
For quite sometime now, the logger keeps on crashing after a a few hours of operation. We've tried various settings and even had a replacement logger but even the replacement logger crashes after a while. Both the original and replacement loggers are
We are using a DT85 to measure the voltage drop over a high resistance (> 1Mohm) with the aid of an external voltage supply. When we limit the supply to a 3V input and thus the measurements to the 3V range on the data logger the measurements are correct as confirmed by use of a multimeter. We would like to measure at higher voltages to get more accurate readings. When using the attenuator howe
I have a running program in DT85, which is having frequency of 5 sec but now I want to change it to 1 minute. How I can do that. My program is in internal Directory .
Hi,
Has anyone managed to connect a SHT7x HUMS sensor to a DT85. It's a digital device using a 2 wire interface (clock/data).
cheers Hillzider
Has anyone had a difficulties of MSDS of battery, shipping company asking us MSDS of internal battery.
If you are helping me i will more than happy.
tolga
Hello,
Thanks to Rudy Gunawan, he answers my last question.
Now I want to use a memory stick with the DT85, USB 3.0, 16 GB, but it doesn't run. I get two errors:
FORMAT A:
Formatting drive A:. Please wait ...
dataTaker 85 E109 - File IO error: Media error (9) 'A:'
dataTaker 85 E104 - Drive format failed at column 10 [ FORMAT A:<err> ]
Exists a limit for the memory siz
tibbie
posted Apr 17 '19 at 12:21 pm
Hello,
As an Environmental Source Samplers company we are thinking to use DT85 on multiple CEMS (continuous emission monitoring system). It will be no problem to view the data that DT85 can send to a FTP server( hourly,..). These CEMS will be located in different country in Asia and US. We are working to build an database interface that configure, control, view, report and send reports to reg
mpb
posted Apr 17 '19 at 12:19 pm
Command window not responding correctly.
Typing password produces output
password
1
DT85>
Typing help commands produces
DT85>
JPF
posted Apr 17 '19 at 11:44 am
Hi,
I'm very new to both dataTaker and LabView, I am trying to connect a DT80 series 2 logger to labview using the DT8x driver, Intermediate level and get outputs from the phase encoder channel (1PE).
I can connect to both dEX web interface through a USB connection and deLogger software through an Ethernet connection as the USB would not work for me and get an output in counts very easil
gid
posted Apr 17 '19 at 11:45 am
Hello
Please i want to get the IP address of the datalogger, so how can i get it?
gid
Good day to you all.
I would like to ask how to do the following:-
I have 3 voltage inputs which will either be 0 or 5 VDC.
I would like to know how to use these inputs to trigger a point on a chart from a PT100 thermistor.
I would also like to ask, is there a switchable output from the DT800 giving 10 VDC output on command and If so how would it be activated?
Please can al
rbrooks
posted Apr 17 '19 at 6:03 am
Hello
We got this device with the intent of being able to monitor and shut down 3 different motors based on temperature.
My concern with the unit was that it only had one relay contact and I have three distinct motors. The distributor assured me that the digital outputs could control Solid State Relays and effect the switching.
I've got it on my desk and I'm issuing state changes to d
mserrao
posted Apr 17 '19 at 6:10 am
Hi all,
First of all I'm a beginner in DT program and I'm from telecom area (just helping a structural monitoring small company).
We have a remote DT with this program:
;BEGIN"A"
;RA1H
;1RELAY=1
;DELAY=3000
;1I(120)
;1+I(120)
;2I(120)
;2+I(120)
;DELAY=3000
;1RELAY=0
;RB12H
;DELAY=8000
;1RELAY=1
;DELAY=600000
;DO{COPYD job=A sched=A dest=ftp://
gregb
posted Apr 17 '19 at 5:58 am
I have been using Deload to unload data from a series 1 DT80. However recently I have been getting the message "file \deload.exe does not exist" when attempting the unload. I have tried the following without success:
reinstalling deload software
running deload from different PC
upgrading DT80 firmware to 9.08
NB I use deload as it saves the schedules to separate csv files, with a header row a
Alas our old reliable DT50 passed away after the power supply suffered an over-voltage incident.
We had regularly gathered data each month still using DeTerminal and an 486DX33 Compaq laptop and with a few changes to the old job program the DT80 is performing well.
There was a command in the old program that I have commented out and after a quick look through the DT50 manual I could no
juult
posted Apr 17 '19 at 5:59 am
Hi,
Does anybody have experience using the calc function in the web interface?
I am trying to make a summarizing counter for a flow, but whatever I try it just gives the value, not a summarised value.
I am using the CALC function.
I have assigned to a channel but it does not seem to make a difference wether I choose Cv or CV+value
Also choosing integrate in advanced does not seem
