Just purchased a DT82EM and having huge issues with it. I upgraded to 9.10 firmware that i was told would resolve the resetting issue.
Essentially as the modem is being tested when it gets to the FTP section the datataker resets and flashes the lights. When it finishes rebooting it displays a message that the datataker was restarted and that memory was cleared.

Any thoughts on how to fix t

We have some DT82EM with older Firmware.
I have upgraded the logger firmware to version V9.18 first, then the modem firmware to version R7.53 (both downloaded from the Datataker website).
After updating the modem the display says "Firmware update failed", but the modem seems to work properly.
I checked the firmware version with

MODEM ON
MODEM FIRMWARE
and got the answer:
B7.

dear sir,
could you please provide full details for configuring DT82EM for noip.com
so that we can access DT82EM from remote using specific domain name of no ip.
pl provide complete settings. i am using vodafone sim right now in internal modem.

regards pradipta

dear sir,
is it possible to send data in .csv format to a particular folder in google drive/dropbox/to some remote computer using ftp or any other method directly using internal modem of DT82EM.

regards
pradipta

Hello Everybody,

I am going to connect a NRG Wind Speed Sensor (NRG#40) to the DT8x as a HSC. You can see link :http://www.renewablenrgsystems.com/products/4350/40C-anemometer-measnet.aspx#

Does DT8x support this NRG's sensor? Please help me.

Thank you very much

thuyvan

Hello All,

I am using DT82EM with Alarm SMS messages and Email Ethernet. I am using 3G network

With Email Ethernet: data (.CSV file) is send to my email. it's OK
But with Alarm SMS messages: Alarm shows " DT82EM3-3 100254: one or more alarm SMS have been lost". It doesn't show my text which i set.
I don't think i have a problem with my 3G network. I think other reason

Please help me

It's not possible to log the median on datataker? If not, how can i access the sample data that statistic sub-schedule uses to make the median calculation by hand?

Hello
My first post here so go easy on me please

Question.....is it possible to setup rainflow analysis using the dEX logging software......or does it need to be done manually?

I have looked at the options and unable to find any reference to it.

Suppose I have 16 strain gauges connected to a CEM, what would the code look like to do a rainflow analysis on all these strain gauges.

dear Sir,
pl note we are trying to configure the dex software for unloading data to a ftp site( configured using file zilla). we have thoroughly followed instruction given in manual. in command window it is shown that unload complete to the specified ftp site. however, the ftp folder contains nothing and after few seconds command window shows session queue full,
unload aborted.

we requi

Hi,

I am receiving Hex data (53 4E 4D 31 32 30 31 36 37 39 45) via a RS232 connection, how can I translate this to readable ASCII?

Regards,
Friedrich

I thought i would try to use dex to reprogram our logger but we have now been having troubles connecting to the datalogger through DEX web interface. We are able to connect via FTP and also via deTransfer so the problem appears to have somethig to do with with dex or network settings.
When we attempt to bring up the web interface, the dex main page shows up, but then when we click on monitor t

Sir ,
How to get the RS-485 data from dEX , i only can find from "Add --> Serial --> SDI12"

If the dEX web interface is on port 80 how do you access the "classic web interface" ?

When I try to set up a connection between my pc and DT80 via USB, The dex Logger software is loading properly but when I hit the configure option the following error shoots.
I have recently upgraded the firmware to the latest version ie v9.10

I need to log temperature from more than 300 thermocouple points connected to dt80's and cem module and need to activate alarm if any exceeds temperature 50 degc.

As a trial run i tried a small program with 3 thermocouple sensors ie if any of the sensor goes above 30 then 1dso should go low.but when i program using dex the alarm is working properly with the last or the third thermocouple but

I finally got Dex running but notice that my interface looks different than what I have seen on youtube videos.

My version is 1.50.012. Is there a newer version available? If so then how to I get it? I couldn't find anything concerning version updates on the DataTaker website.

Thanks in advance.

Hi,

I've received this message when starting up my DT, which had already been running for some time. It states there's no active configuration. My DEX configuration was still stored, I just needed to restart the logger. I faced this issue another time when I reprogrammed a DT remotely, and noticed the next day, that the configuration wasn't active.

Anyone else faced this problem? Is there

Our port 80 blocked by the all mobile carriers,how to change this web service port? So dEX can be used again.

Good morning!

I was wondering if there is a way to view a configuration file (.dex) that is saved on my computer without a dataTaker device connected (in my case, a DT85). Due to my current setup/ deployment of the data logger, it is inconvenient to spend much time with the computer down at the dataTaker. It's easier to work on the configuration at my desk, and then quickly load the file to t

Is there a way to specify a channel factor when setting up measurements using dEX? I need to account for a 100 ohm shunt resistor in a 4-20 mA measurement. The program generated by dEX does not seem to have a place to include this value.