Hello,
The integrated DT80 in our system has lost its configuration (no current job).
It seems thats the DT80 have run out of memory space, and is unable to load the configurated jobs at start up. As descibded in its logs with the error E116 :

EVENT ,2023/04/21,00:39:25,0.003906,"Reset 9.22.9125 POWERUP/BUTTON (c0a00005)"
EVENT ,2023/04/21,00:39:25,0.552124,"Beginning entry of job "

Hello, I am new to the DT82em so please forgive my ignorance. I have been asked by my company who own the Datataker to wipe the memory and create a new schedule. The issue is the last person has password protected the unit and we need to wipe the device. WE want to lose the data and software. The version number is a 9.22.
Thank you

Hi, We're using DT85G Series 4 for monitoring settlement and strain gauge readings.

I was wondering if anyone here can help me monitor the data using microsoft excel (Data connections). For now, we are more inclined in using Delogger5 as it is easier to program than Dex.

For now we are monitoring the data using the Txt window in Delogger5 but we prefer to do it Microsoft excel for data

Hello,
I hope you are well.
I have a DT85 series 4 datalogger and I want to measure the torque + rotation speed + power from my torque sensor, which has a 12 pin connector (picture attached). I have also attached the manual for the torque meter (DRBK from applied measurements). I have also attached the datalogger manual.
Any help would be greatly appreciated.
Thanks!

Hi
I am working on a train project presently trying to program my dt80m3-3 with code to take in GPS data and use that data to monitor and record train speed and trigger appropriate data storage responses depending on train stop/run. Also want to record GPS position.
Can someone please assist with some appropriate coding. I am using deX-2.

Hi, I have a couple of DataTaker DT80's (one series 2, one series 4).

I plugged the S4 into a Windows 10 PC and Windows said it was installing a driver. Would this be DTusb or do I need to physically download it (where from?) and install it first?

I see from other posts that DEX 2.0 avoids the need for Flash. Where is the download for DEX2.0? Do I need to upgrade the DT80 firmware firs

Hi All

I goofed today, and set the logging interval much shorter than usual (2 vs my usual 15 or 30 seconds), ran out of memory half way through my trial and overwrote the early data.

I have downloaded and dumped the DDB - it's still missing the first two hours or so, so I'm fairly sure they are gone.

I was watching the data in a DEX2 dashboard while it was being collected - long shot

Hi
My DT80 series 2 just stopped responding
The sample light, disk and power lights are on but no display
It was a brand new logger (2009?) . I had updated to latest firmware.
It was working fine for about 3 weeks
Anyone got any ideas ? A hard reset has not fixed it
thanks

Hi @all,
I'm currently evaluating a DT80M Datataker Logger for the use with our SDI12 Moisture sensors. Logging the data works fine so far but I hit a strange problem uploading the data to an FTP server. Every time the Logger tries to upload data, it fails with some strange 'FTP: server out of sync (-3)' error.

DT80> SESSION: Starting (manual)
SESSION: Ready (MEDIONmobi,3G-HSPA,-93dB

Hi all, I last set up my DT85 on dex-2 about six months ago and have unfortunately forgotten how to do it. I am sure that the IP address and port 80 are fine but think there is something to do with the template that I am missing? Could any please provide me with the chronological steps I need to do as at the moment it keeps saying my DT85 is offline.

Thanks :)

Hi all

One of our DT85 stop working yesterday.
The display is working(has display when bootstrap) but nothing display.
Sample, disk and power LED is On.
Hard reboot is not working too.

Any advices?

Many thanks

cách lập trình và so sánh giá trị trigger cho relay trên DT82E bằng phần mềm DEX-2
Ví dụ: Tôi muốn đo một bộ nhiệt độ từ 0 độ C đến 1000 độ C. Tôi muốn lấy bất kỳ giá trị nào n

Hi,
In order to drive cooling fans for my system, I need a dynamic voltage output (2 different values) depending on measured temperature.
I have a DT80 series 4 logging temperature values.
I was wondering if the DAC could achieves this function using alarms?
I was only able to set the dac output value with manual commands, and the doculmentation is not really exhaustive on how to driv

I'm sure this is a simple question, but I can't find the answer!
I want to establish a direct connection to the command interface over a local network using my software. The final aim is to have scripts running on a linux web server retreiving real time measurements from the DT80.
The DT80 is happily running on a local network, and there is no problem connecting with deTransfer and other ut

Hey,

I just started using the DT80 series 4 and when I tried to connect the logger and it have been only showing "Connecting to logger.....please wait"

-I've rebooted the device,
-Connected it locally by the usb
-Configured a new IP address to connect it virtually
-I used firefox mozille to open the virtual page and it only shows "connecting to device.. please wait" the DT80 is

We currently have DT80G devices in the field that upload to a FTP server. Is there a way to use a more secure upload channel?

I am still wrapping my head around this but there appears to be devices that can connect to MODBUS and could then handle the uploads. But I am not sure how all this stuff works and if I even technically understand how these things work

Dear DataTaker experts,
I am using DT85G Series 3, and before 2020, It was worked with dEX previous version without any issue. However, as it no longer work with flash player now I have to upgrade it to dEX 2.0 and firmware also upgraded to version 9.22


I have connected the logger using Ethernet cable and add the logger to dEX-2.
Now I cannot access the logger through the dEX-2 d

I measure wrong voltages at any analog input.
The measured values are only 83% of the actual voltage applied.

Please find the result of the self test here:
Selftest

Is there anything I can do?
How can I send the logger for repair?

Regards
Jürgen

I have a requirement whereby i will have 2 DT85s in separate buildings both on different networks but pc has access to both networks, that i want to have 1 dt85 connected to the other or someway of having one download where all channels from both logger be on the one download.

I have data taker DT85W. I was heat up and now showing REFT error. How it can be rectified. Do I need to send it for repair or not