what does this mean?

"tc_tcp_timeout() (freeze case), loops=115, recovering"

We need a simple way to totalizer a slow pulse from water meters and the same time reset counter each datalogging. Reset is easy using dEX with “Reset Counter”, but ”doesn’t exist the “Totalizer Counter for ever”

Thanks in advance

Hello Rudy, Is there any way to assign a manual channels whole consumption (mA) in any interval (hour/day/etc...).

Best Regards
Gonzalo

I realize this probably isn't the correct forum to ask about Cybertec 1100 but there seems to be a bunch of networking pros here with some experience with Cybertec 1100, so here goes.

I am trying to make wireless dial in a Cybertec 1100 using hyperterminal with TCP/IP. Since wireless IP address are quite expensive over here, I will use dynamic IP with DDNS on the modem.

Registered with

Current profile in a remote location, GPRS network weak with frequent signal breaks. Current profile data very 10 minutes:

16 C811 70802 2008 3 28 12 21 52 3 0 1 2 40 200 100 10 1
0 0 0 2886 17424 0 0 0 0 0 15425
0 0 0 0 61 191 65 193 14 16 18 0 110 192 0 107
1 -1399 -2174 -172 0 0 0 129 131 162
2 -1412 -2378 -294 0

Here is a quote from Datataker Australia:


USB Memory Stick: We do not recommend the use of USB flash drives for logging as they are not robust and the DT80 does not have any retaining mechanism to retain the drive, it can fall out.


Does "DT80 does not have any retaining mechanism to retain the drive, it can fall out" means the USB stick PHYSICALLY fall off the slot? or does it mean data

Is there a way of including prior measured lead resistance into thermistor measurement description setup for a two wire measurement (similar as how parallel shunt resistor is included)?

This could default to zero but when known allow for a more correct temperature calculations to be performed particular at the higher temperatures (lower thermistor resistance region where lead resistance has

Hello again,

How do I get the time on my CSV file to be display as 15:39:41 instead of just 15:39? I set P39=0, but it didn't seem to do anything. Thanks!

Hi,

If I connect a PT100 directly to the dataTaker, correct values are obtained, no problem. We have a PT100 on a test rig connected to a PLC as a 3 way system, that is, the 2 red wires connect to the same point.

If we connect the dataTaker off the same connections, the values are incorrect on the dataTaker and the PLC. How can I overcome this problem.

Many thanks,
Nick.

Dear Sir,

we are using DT85G for measurement of various sensors such as vibrating wire type stress capsules, loadcells, potentiometric sensors, voltage and 4 to 20mA current loop sensors. entire set up will be installed in mine for data logging ( continuous monitoring). we need to configure a HMI panel to display all the measurements, alarms etc. we are using HMI of Kinco Electric ( Model MT4

Hello All,

I have a DT85 Serie 1 Data logger with the latest firmware and am trying to display 5 thermocouple temperatures in Labview on an XY Graph.

So far I managed to configure the TCP/IP sample real-time waveform driver to fetch 5 temperatures from the DataTaker, and from there I can display the temperatures and associated timestamp on a Labview indicator, but I am having difficulty

Hello,

I have a bunch of numerical data I am reading in Labview with the Low Level 'Read Realtime' VI. I also have the DT85 calculate a time difference with the DT command and read the string through the 'Read Line' VI. The issue I have is that the DT command returns a string in the HH:MM:SS.mmm format.

I was wondering if there is a way to format the string so that I can receive it in La

I'm working on and app to work in conjunction with the schedules I'm running on the logger. The purpose of this app is to enter 'device under test' serial numbers and operator badges. I need this data to be logged with the test data, but the fact that logged data is being echoed out the "host port", it's stepping on my communications.

How do I suppress the echoing, yet maintain the logging?

Has anyone developed any macros or apps for presenting the CSV files of logged data as a line chart or to clean up columns, etc....... and would they be willing to share?

Thanks in advance

Dear Sir,

Pl let me know how to communicate DT85 with Tablet and access dEX Software using (through Chrome or other web browser) Tablet.

What should be the minimum hardware and software configuration for above case?

Regards,
Gpradipta

I have a sensor TSL235R - LIGHT-TO-FREQUENCY CONVERTER, datasheet - http://www.rhydolabz.com/documents/sensors/TSL235R_LF.pdf

It provides linear response of ambient irradiance to output frequency. How can I measure this output frequency with a datalogger ?

CP

Has anyone had a difficulties of MSDS of battery, shipping company asking us MSDS of internal battery.

If you are helping me i will more than happy.

tolga

Hello,
Thanks to Rudy Gunawan, he answers my last question.

Now I want to use a memory stick with the DT85, USB 3.0, 16 GB, but it doesn't run. I get two errors:
FORMAT A:
Formatting drive A:. Please wait ...
dataTaker 85 E109 - File IO error: Media error (9) 'A:'
dataTaker 85 E104 - Drive format failed at column 10 [ FORMAT A:<err> ]

Exists a limit for the memory siz

Hello,

As an Environmental Source Samplers company we are thinking to use DT85 on multiple CEMS (continuous emission monitoring system). It will be no problem to view the data that DT85 can send to a FTP server( hourly,..). These CEMS will be located in different country in Asia and US. We are working to build an database interface that configure, control, view, report and send reports to reg

Hi,

I'm very new to both dataTaker and LabView, I am trying to connect a DT80 series 2 logger to labview using the DT8x driver, Intermediate level and get outputs from the phase encoder channel (1PE).

I can connect to both dEX web interface through a USB connection and deLogger software through an Ethernet connection as the USB would not work for me and get an output in counts very easil